# Dictionary Definition

cogwheel n : a toothed wheel that engages another
toothed mechanism in order to change the speed or direction of
transmitted motion [syn: gear, gear
wheel]

# User Contributed Dictionary

## English

### Noun

# Extensive Definition

A gear is a component within a transmission
device that transmits rotational force to another
gear or device. A gear is different from a pulley in that a gear is a round
wheel which has linkages ("teeth" or "cogs") that mesh with other
gear teeth, allowing force to be fully transferred without
slippage. Depending on their construction and arrangement, geared
devices can transmit forces at different speeds, torques, or in a different
direction, from the power source. Gears are a very useful simple
machine. The most common situation is for a gear to mesh with
another gear, but a gear can mesh with any device having compatible
teeth, such as linear moving racks.
A gear's most important feature is that gears of unequal sizes
(diameters) can be combined to produce a mechanical
advantage, so that the rotational speed and torque of the
second gear are different from that of the first.

In the context of a particular machine, the term
"gear" also refers to one particular arrangement of gears among
other arrangements (such as "first gear"). Such arrangements are
often given as a ratio, using the number of teeth or gear diameter
as units. The term "gear" is also used in non-geared devices which
perform equivalent tasks:

- "...broadly speaking, a gear refers to a ratio of engine shaft speed to driveshaft speed. Although CVTs change this ratio without using a set of planetary gears, they are still described as having low and high "gears" for the sake of convention."

## Mechanical advantage

The interlocking of the teeth in a pair of meshing gears means that their circumferences necessarily move at the same rate of linear motion (eg., metres per second, or feet per minute). Since rotational speed (eg. measured in revolutions per second, revolutions per minute, or radians per second) is proportional to a wheel's circumferential speed divided by its radius, we see that the larger the radius of a gear, the slower will be its rotational speed, when meshed with a gear of given size and speed. The same conclusion can also be reached by a different analytical process: counting teeth. Since the teeth of two meshing gears are locked in a one to one correspondence, when all of the teeth of the smaller gear have passed the point where the gears meet -- ie., when the smaller gear has made one revolution -- not all of the teeth of the larger gear will have passed that point -- the larger gear will have made less than one revolution. The smaller gear makes more revolutions in a given period of time; it turns faster. The speed ratio is simply the reciprocal ratio of the numbers of teeth on the two gears.(Speed A * Number of teeth A) = (Speed B * Number
of teeth B)

This ratio is known as the gear
ratio.

The torque ratio can be determined by considering
the force that a tooth of one gear exerts on a tooth of the other
gear. Consider two teeth in contact at a point on the line joining
the shaft axes of the two gears. In general, the force will have
both a radial and a circumferential component. The radial component
can be ignored: it merely causes a sideways push on the shaft and
does not contribute to turning. The circumferential component
causes turning. The torque is equal to the
circumferential component of the force times radius. Thus we see
that the larger gear experiences greater torque; the smaller gear
less. The torque ratio is equal to the ratio of the radii. This is
exactly the inverse of the case with the velocity ratio. Higher
torque implies lower velocity and vice versa. The fact that the
torque ratio is the inverse of the velocity ratio could also be
inferred from the law of conservation of energy. Here we have been
neglecting the effect of friction on the torque ratio. The velocity
ratio is truly given by the tooth or size ratio, but friction will
cause the torque ratio to be actually somewhat less than the
inverse of the velocity ratio.

In the above discussion we have made mention of
the gear "radius". Since a gear is not a proper circle but a
roughened circle, it does not have a radius. However, in a pair of
meshing gears, each may be considered to have an effective radius,
called the pitch radius, the pitch radii being such that smooth
wheels of those radii would produce the same velocity ratio that
the gears actually produce. The pitch radius can be considered sort
of an "average" radius of the gear, somewhere between the outside
radius of the gear and the radius at the base of the teeth.

The issue of pitch radius brings up the fact that
the point on a gear tooth where it makes contact with a tooth on
the mating gear varies during the time the pair of teeth are
engaged; also the direction of force may vary. As a result, the
velocity ratio (and torque ratio) is not, actually, in general,
constant, if one considers the situation in detail, over the course
of the period of engagement of a single pair of teeth. The velocity
and torque ratios given at the beginning of this section are valid
only "in bulk" -- as long-term averages; the values at some
particular position of the teeth may be different.

It is in fact possible to choose tooth shapes
that will result in the velocity ratio also being absolutely
constant -- in the short term as well as the long term. In good
quality gears this is usually done, since velocity ratio
fluctuations cause undue vibration, and put additional stress on
the teeth, which can cause tooth breakage under heavy loads at high
speed. Constant velocity ratio may also be desirable for precision
in instrumentation gearing, clocks and watches. The involute
tooth shape is one that results in a constant velocity ratio, and
is the most commonly used of such shapes today.

## Comparison with other drive mechanisms

The definite velocity ratio which results from having teeth gives gears an advantage over other drives (such as traction drives and V-belts) in precision machines such as watches that depend upon an exact velocity ratio. In cases where driver and follower are in close proximity gears also have an advantage over other drives in the reduced number of parts required; the downside is that gears are more expensive to manufacture and their lubrication requirements may impose a higher operating cost.The automobile transmission
allows selection between gears to give various mechanical
advantages.

## Gear types

### External vs. internal gears

An external gear is one with the teeth formed on the outer surface of a cylinder or cone. Conversely, an internal gear is one with the teeth formed on the inner surface of a cylinder or cone. For bevel gears, an internal gear is one with the pitch angle exceeding 90 degrees.### Helical gears

Helical gears offer a refinement over spur gears. The leading edges of the teeth are not parallel to the axis of rotation, but are set at an angle. Since the gear is curved, this angling causes the tooth shape to be a segment of a helix. The angled teeth engage more gradually than do spur gear teeth. This causes helical gears to run more smoothly and quietly than spur gears. Helical gears also offer the possibility of using non-parallel shafts. A pair of helical gears can be meshed in two ways: with shafts oriented at either the sum or the difference of the helix angles of the gears. These configurations are referred to as parallel or crossed, respectively. The parallel configuration is the more mechanically sound. In it, the helices of a pair of meshing teeth meet at a common tangent, and the contact between the tooth surfaces will, generally, be a curve extending some distance across their face widths. In the crossed configuration, the helices do not meet tangentially, and only point contact is achieved between tooth surfaces. Because of the small area of contact, crossed helical gears can only be used with light loads.Quite commonly, helical gears come in pairs where
the helix angle of one is the negative of the helix angle of the
other; such a pair might also be referred to as having a right
handed helix and a left handed helix of equal angles. If such a
pair is meshed in the 'parallel' mode, the two equal but opposite
angles add to zero: the angle between shafts is zero -- that is,
the shafts are parallel. If the pair is meshed in the 'crossed'
mode, the angle between shafts will be twice the absolute value of
either helix angle.

Note that 'parallel' helical gears need not have
parallel shafts -- this only occurs if their helix angles are equal
but opposite. The 'parallel' in 'parallel helical gears' must
refer, if anything, to the (quasi) parallelism of the teeth, not to
the shaft orientation.

As mentioned at the start of this section,
helical gears operate more smoothly than do spur gears. With
parallel helical gears, each pair of teeth first make contact at a
single point at one side of the gear wheel; a moving curve of
contact then grows gradually across the tooth face. It may span the
entire width of the tooth for a time. Finally, it recedes until the
teeth break contact at a single point on the opposite side of the
wheel. Thus force is taken up and released gradually. With spur
gears, the situation is quite different. When a pair of teeth meet,
they immediately make line contact across their entire width. This
causes impact stress and noise. Spur gears make a characteristic
whine at high speeds and can not take as much torque as helical
gears because their teeth are receiving impact blows. Whereas spur
gears are used for low speed applications and those situations
where noise control is not a problem, the use of helical gears is
indicated when the application involves high speeds, large power
transmission, or where noise abatement is important. The speed is
considered to be high when the pitch line velocity (that is, the
circumferential velocity) exceeds 5000 ft/min. A disadvantage of
helical gears is a resultant thrust along the axis of the gear,
which needs to be accommodated by appropriate thrust
bearings, and a greater degree of sliding friction between the
meshing teeth, often addressed with specific additives in the
lubricant.

### Double helical gears

Double helical gears, also known as herringbone gears, overcome the problem of axial thrust presented by 'single' helical gears by having teeth that set in a 'V' shape. Each gear in a double helical gear can be thought of as two standard, but mirror image, helical gears stacked. This cancels out the thrust since each half of the gear thrusts in the opposite direction. They can be directly interchanged with spur gears without any need for different bearings.Where the oppositely angled teeth meet in the
middle of a herringbone gear, the alignment may be such that tooth
tip meets tooth tip, or the alignment may be staggered, so that
tooth tip meets tooth trough. The latter type of alignment results
in what is known as a Wuest type herringbone gear.

With the older method of fabrication, herringbone
gears had a central channel separating the two oppositely-angled
courses of teeth. This was necessary to permit the shaving tool to
run out of the groove. The development of the Sykes gear shaper
now makes it possible to have continuous teeth, with no central
gap.

### Bevel gears

Bevel gears are essentially conically shaped,
although the actual gear does not extend all the way to the vertex
(tip) of the cone that bounds it. With two bevel gears in mesh, the
vertices of their two cones lie on a single point, and the shaft
axes also intersect at that point. The angle between the shafts can
be anything except zero or 180 degrees. Bevel gears with equal
numbers of teeth and shaft axes at 90 degrees are called miter
gears.

The teeth of a bevel gear may be straight-cut as
with spur gears, or they may be cut in a variety of other shapes.
Spiral bevel gears have teeth that are both curved along their (the
tooth's) length; and set at an angle, analogously to the way
helical gear teeth are set at an angle compared to spur gear teeth.
Zero bevel gears have teeth which are curved along their length,
but not angled. Spiral bevel gears have the same advantages and
disadvantages relative to their straight-cut cousins as helical
gears do to spur gears. Straight bevel gears are generally used
only at speeds below 5 m/s (1000 ft/min), or, for small gears, 1000
r.p.m.

#### Crown gear

A crown gear or contrate gear is a particular form of bevel gear whose teeth project at right angles to the plane of the wheel; in their orientation the teeth resemble the points on a crown. A crown gear can only mesh accurately with another bevel gear, although crown gears are sometimes seen meshing with spur gears. A crown gear is also sometimes meshed with an escapement such as found in mechanical clocks.### Hypoid gears

main article Hypoid Hypoid gears resemble spiral bevel gears, except that the shaft axes are offset, not intersecting. The pitch surfaces appear conical but, to compensate for the offset shaft, are in fact hyperboloids of revolution. Hypoid gears are almost always designed to operate with shafts at 90 degrees. Depending on which side the shaft is offset to, relative to the angling of the teeth, contact between hypoid gear teeth may be even smoother and more gradual than with spiral bevel gear teeth. Also, the pinion can be designed with fewer teeth than a spiral bevel pinion, with the result that gear ratios of 60:1 and higher are "entirely feasible" using a single set of hypoid gears.### Worm gear

A worm is a gear that resembles a screw. It is a species of helical
gear, but its helix angle is usually somewhat large(ie., somewhat
close to 90 degrees) and its body is usually fairly long in the
axial direction; and it is these attributes which give it its screw
like qualities. A worm is usually meshed with an ordinary looking,
disk-shaped gear, which is called the "gear", the "wheel", the
"worm gear", or the "worm wheel". The prime feature of a
worm-and-gear set is that it allows the attainment of a high gear
ratio with few parts, in a small space. Helical gears are, in
practice, limited to gear ratios of 10:1 and under; worm gear sets
commonly have gear ratios between 10:1 and 100:1, and occasionally
500:1. In worm-and-gear sets, where the worm's helix angle is
large, the sliding action between teeth can be considerable, and
the resulting frictional loss causes the efficiency of the drive to
be usually less than 90 percent, sometimes less than 50 percent,
which is far less than other types of gears.

The distinction between a worm and a helical gear
is made when at least one tooth persists for a full 360 degree turn
around the helix. If this occurs, it is a 'worm'; if not, it is a
'helical gear'. A worm may have as few as one tooth. If that tooth
persists for several turns around the helix, the worm will appear,
superficially, to have more than one tooth, but what one in fact
sees is the same tooth reappearing at intervals along the length of
the worm. The usual screw nomenclature applies: a one-toothed worm
is called "single thread" or "single start"; a worm with more than
one tooth is called "multiple thread" or "multiple start".

We should note that the helix angle of a worm is
not usually specified. Instead, the lead angle, which is equal to
90 degrees minus the helix angle, is given.

In a worm-and-gear set, the worm can always drive
the gear. However, if the gear attempts to drive the worm, it may
or may not succeed. Particularly if the lead angle is small, the
gear's teeth may simply lock against the worm's teeth, because the
force component circumferential to the worm is not sufficient to
overcome friction. Whether this will happen depends on a function
of several parameters; however, an approximate rule is that if the
tangent of the lead angle is greater than the coefficient of
friction, the gear will not lock. Worm-and-gear sets that do lock
in the above manner are called "self locking". The self locking
feature can be an advantage, as for instance when it is desired to
set the position of a mechanism by turning the worm and then have
the mechanism hold that position. An example of this is the tuning
mechanism on some types of stringed instruments.

If the gear in a worm-and-gear set is an ordinary
helical gear only point contact between teeth will be achieved. If
medium to high power transmission is desired, the tooth shape of
the gear is modified to achieve more intimate contact with the worm
thread. A noticeable feature of most such gears is that the tooth
tops are concave, so that the gear partly envelopes the worm. A
further development is to make the worm concave (viewed from the
side, perpendicular to its axis) so that it partly envelopes the
gear as well; this is called a cone-drive or Hindley worm.

A right hand helical gear or right hand worm is
one in which the teeth twist clockwise as they recede from an
observer looking along the axis. The designations, right hand and
left hand, are the same as in the long established practice for
screw threads, both external and internal. Two external helical
gears operating on parallel axes must be of opposite hand. An
internal helical gear and its pinion must be of the same
hand.

A left hand helical gear or left hand worm is one
in which the teeth twist counterclockwise as they recede from an
observer looking along the axis.

### Rack and pinion

A rack is a toothed bar or rod that can be thought of as a sector gear with an infinitely large radius of curvature. Torque can be converted to linear force by meshing a rack with a pinion: the pinion turns; the rack moves in a straight line. Such a mechanism is used in automobiles to convert the rotation of the steering wheel into the left-to-right motion of the tie rod(s). Racks also feature in the theory of gear geometry, where, for instance, the tooth shape of an interchangeable set of gears may be specified for the rack (infinite radius), and the tooth shapes for gears of particular actual radii then derived from that. The rack and pinion gear type is employed in a rack railway.### Sun and planet gear

## Epicyclic gearing

In an ordinary gear train, the gears rotate but
their axes are stationary. An epicyclic
gear train is one in which one or more of the axes also moves.
Examples are the sun and planet gear system invented by the company
of James
Watt, in which the axis of the planet gear revolves around the
central sun gear; and the differential gear system used to drive
the wheels of automobiles, in which the axis of the central bevel
pinion is turned "end over end" by the ring gear, the drive to the
wheels being taken off by bevel gears meshing with the central
bevel pinion. With the differential gearing, the sum of the two
wheel speeds is fixed, but how it is divided between the two wheels
is undetermined, so the outer wheel can run faster and the inner
wheel slower on corners.

## Nomenclature

### General nomenclature

Common abbreviations:

n. Rotational velocity. (Measured, for
example, in r.p.m.) ω Angular
velocity. (Radians per unit time.)
(1 r.p.m. = π/30 radians per second.)
N. Number of teeth.

Gear terminology:

Gear or wheel. The larger of two interacting
gears. Pinion. The smaller gear in a pair. Path of contact. The
path followed by the point of contact between two meshing gear
teeth. Line of action, also called Pressure line. The line along
which the force between two meshing gear teeth is directed. It has
the same direction as the force vector. In general, the line of
action changes from moment to moment during the period of
engagement of a pair of teeth. For involute gears, however, the
tooth-to-tooth force is always directed along the same line -- that
is, the line of action is constant. this implies that for involute
gears the path of contact is also a straight line, coincident with
the line of action -- as is indeed the case.

Further note on tooth force: If two rigid objects
make contact, they always do so at a point (or points) where the
tangents to their surfaces coincide -- that is, where there is a
common tangent. The perpendicular to the common tangent at the
point of contact is called the common normal. Ignoring friction,
the force exerted by the objects on each other is always directed
along the common normal. Thus, for meshing gear teeth, the line of
action is the common normal to the tooth surfaces. Axis. The axis
of revolution of the gear; center line of the shaft. Pitch point
(p). The point where the line of action crosses a line joining the
two gear axes. Pitch circle. A circle, centered on and
perpendicular to the axis, and passing through the pitch point.
Sometimes also called the pitch line, although it is a circle.
Pitch diameter (D). Diameter of a pitch circle. Equal to twice the
perpendicular distance from the axis to the pitch point. The
nominal gear size is usually the pitch diameter. Module (m). The
module of a gear is equal to the pitch diameter divided by the
number of teeth. . Operating pitch diameters. The pitch diameters
determined from the number of teeth and the center distance at
which gears operate.

## Tooth profile

A profile is one side of a tooth in a cross section between the outside circle and the root circle. Usually a profile is the curve of intersection of a tooth surface and a plane or surface normal to the pitch surface, such as the transverse, normal, or axial plane.The fillet curve (root fillet) is the concave
portion of the tooth profile where it joins the bottom of the tooth
space.2

As mentioned near the beginning of the article,
the attainment of a non fluctuating velocity ratio is dependent on
the profile of the teeth. Friction and wear
between two gears is also dependent on the tooth profile. There are
a great many tooth profiles that will give a constant velocity
ratio, and in many cases, given an arbitrary tooth shape, it is
possible to develop a tooth profile for the mating gear that will
give a constant velocity ratio. However, two constant velocity
tooth profiles have been by far the most commonly used in modern
times. They are the cycloid and
the involute.
The cycloid was more common until the late 1800s; since then the
involute has largely superseded it, particularly in drive train
applications. The cycloid is in some ways the more interesting and
flexible shape; however the involute has two advantages: it is
easier to manufacture, and it permits the center to center spacing
of the gears to vary over some range without ruining the constancy
of the velocity ratio. Cycloidal gears only work properly if the
center spacing is exactly right. Cycloidal gears are still used in
mechanical clocks.

### Undercut

Undercut is a condition in generated gear teeth when any part of the fillet curve lies inside of a line drawn tangent to the working profile at its point of juncture with the fillet. Undercut may be deliberately introduced to facilitate finishing operations. With undercut the fillet curve intersects the working profile. Without undercut the fillet curve and the working profile have a common tangent.## Pitch

Pitch is the distance between a point on one tooth and the corresponding point on an adjacent tooth. It is a dimension measured along a line or curve in the transverse, normal, or axial directions. The use of the single word “pitch” without qualification may be ambiguous, and for this reason it is preferable to use specific designations such as transverse circular pitch, normal base pitch, axial pitch.### Circular pitch, p

Circular pitch is the arc distance along a specified pitch circle or pitch line between corresponding profiles of adjacent teeth.### Transverse circular pitch, pt

Transverse circular pitch is the circular pitch in the transverse plane.### Normal circular pitch, pn, pe

Normal circular pitch is the circular pitch in the normal plane, and also the length of the arc along the normal pitch helix between helical teeth or threads.### Axial pitch, px

Axial pitch is linear pitch in an axial plane and in a pitch surface. In helical gears and worms, axial pitch has the same value at all diameters. In gearing of other types, axial pitch may be confined to the pitch surface and may be a circular measurement.The term axial pitch is preferred to the term
linear pitch. The axial pitch of a helical worm and the circular
pitch of its wormgear are the same.

### Normal base pitch, pN, pbn

Normal base pitch in an involute helical gear is the base pitch in the normal plane. It is the normal distance between parallel helical involute surfaces on the plane of action in the normal plane, or is the length of arc on the normal base helix. It is a constant distance in any helical involute gear.### Transverse base pitch, pb, pbt

Base pitch in an involute gear is the pitch on the base circle or along the line of action. Corresponding sides of involute gear teeth are parallel curves, and the base pitch is the constant and fundamental distance between them along a common normal in a transverse plane.### Diametral pitch (transverse), Pd

Diametral pitch (transverse) is the ratio of the number of teeth to the standard pitch diameter in inches.P_ = \frac = \frac = \frac

### Normal diametral pitch, Pnd

Normal diametral pitch is the value of diametral pitch in a normal plane of a helical gear or worm.P_ = \frac

### Angular pitch, θN, τ

Angular pitch is the angle subtended by the circular pitch, usually expressed in radians.\tau = \frac degrees or \frac radians

## Cage gear

The cage gear, also called lantern gear or lantern pinion, has been used for centuries. Its teeth are cylindrical rods, parallel to the axle and arranged in a circle around it, much as the bars on a round bird cage or lantern. The assembly is held together by disks at either end into which the tooth rods and axle are set.## Gear materials

Numerous nonferrous alloys, cast irons, powder-metallurgy and even plastics are used in the manufacture of gears. However steels are most commonly used because of their high strength to weight ratio and low cost. Plastic is commonly used where cost or weight is a concern. A properly designed plastic gear can replace steel in many cases; It often has desirable properties. They can tolerate dirt, low speed meshing, and "skipping" quite well. Manufacturers have employed plastic to make consumer items affordable. This includes copy machines, optical storage devices, VCRs, cheap dynamos, consumer audio equipment, servo motors, and printers.## Tooth thickness

### Circular thickness

Circular thickness is the length of arc between the two sides of a gear tooth, on the specified datum circle.### Transverse circular thickness

Transverse circular thickness is the circular thickness in the transverse plane.### Normal circular thickness

Normal circular thickness is the circular thickness in the normal plane. In a helical gear it may be considered as the length of arc along a normal helix.### Axial thickness

Axial thickness in helical gears and worms is the tooth thickness in an axial cross section at the standard pitch diameter.### Base circular thickness

Base circular thickness in involute teeth is the length of arc on the base circle between the two involute curves forming the profile of a tooth.### Normal chordial thickness

Chordal thickness is the length of the chord that subtends a circular thickness arc in the plane normal to the pitch helix. Any convenient measuring diameter may be selected, not necessarily the standard pitch diameter.### Chordial addendum (chordial height)

Chordal addendum (chordal height) is the height from the top of the tooth to the chord subtending the circular thickness arc. Any convenient measuring diameter may be selected, not necessarily the standard pitch diameter.### Profile shift

The profile shift is the displacement of the basic rack datum line from the reference cylinder, made non-dimensional by dividing by the normal module. It is used to specify the tooth thickness, often for zero backlash.### Rack shift

The rack shift is the displacement of the tool datum line from the reference cylinder, made non-dimensional by dividing by the normal module. It is used to specify the tooth thickness.### Measurement over pins

Measurement over pins is the measurement of the distance taken over a pin positioned in a tooth space and a reference surface. The reference surface may be the reference axis of the gear, a datum surface or either one or two pins positioned in the tooth space or spaces opposite the first. This measurement is used to determine tooth thickness.### Span measurement

Span measurement is the measurement of the distance across several teeth in a normal plane. As long as the measuring device has parallel measuring surfaces that contact on an unmodified portion of the involute, the measurement will be along a line tangent to the base cylinder. It is used to determine tooth thickness.### Modified addendum teeth

Teeth of engaging gears, one or both of which have non-standard addendum.### Full-depth teeth

Full-depth teeth are those in which the working depth equals 2.000 divided by the normal diametral pitch.### Stub teeth

Stub teeth are those in which the working depth is less than 2.000 divided by the normal diametral pitch.### Equal addendum teeth

Equal addendum teeth are those in which two engaging gears have equal addendums.### Long and short-addendum teeth

Long and short addendum teeth are those in which the addendums of two engaging gears are unequal.## Gear Design Based upon Module System

Countries which have adopted the metric
system generally use the module system. As a result, the term
module is usually understood to mean the pitch diameter in
millimeters divided by the number of teeth. When the module is
based upon inch measurements, it is known as The English Module to
avoid confusion with the metric module. Module is an actual
dimension, whereas diametral pitch is only a ratio. Thus, if the
pitch diameter of a gear is 40 millimeters and the number of teeth
20, the module is 2, which means that there are 2 millimeters of
pitch diameter for each tooth.

## See also

## References

## General sources

- Earle Buckingham, Analytical Mechanics of Gears; 1988, Mineola, New York, USA; Dover. First copyright 1949 by Earle Buckingham. This is an influential treatise on gears. Advanced Level.
- Venton Levy Doughty and Alex Vallance, Design of Machine Members, 4th edition; 1964; McGraw Hill. First edition was 1936. This is an engineering text on machine parts. It has two chapters on gears.
- McGraw-Hill Encyclopedia of Science and Technology. 2002.
- American National Standards Institute (ANSI) / American Gear Manufacturers Association (AGMA) 1012-G05, "Gear Nomenclature, Definition of Terms with Symbols". The definitive source of gear specifications.
- American Gear Manufacturers Association website

## External links

cogwheel in Catalan: Engranatge

cogwheel in Czech: Ozubené kolo

cogwheel in Danish: Tandhjul

cogwheel in German: Zahnrad

cogwheel in Estonian: Hammasratas

cogwheel in Spanish: Engranaje

cogwheel in Esperanto: Dentrado

cogwheel in Persian: چرخدنده

cogwheel in French: Engrenage

cogwheel in Korean: 톱니바퀴

cogwheel in Ido: Ingrano

cogwheel in Italian: Ingranaggio

cogwheel in Hebrew: גלגל שיניים

cogwheel in Lithuanian: Krumpliaratis

cogwheel in Hungarian: Fogaskerék

cogwheel in Malayalam: പല്ച്ചക്രം

cogwheel in Burmese: ဂီယာ

cogwheel in Dutch: Tandwiel

cogwheel in Japanese: 歯車

cogwheel in Norwegian: Tannhjul

cogwheel in Norwegian Nynorsk: Tannhjul

cogwheel in Polish: Koło zębate

cogwheel in Portuguese: Engrenagem

cogwheel in Romanian: Roată dinţată

cogwheel in Russian: Зубчатое колесо

cogwheel in Simple English: Gear

cogwheel in Slovak: Ozubené koleso

cogwheel in Slovenian: Zobnik

cogwheel in Finnish: Hammaspyörä

cogwheel in Swedish: Kugghjul

cogwheel in Turkish: Dişli çark

cogwheel in Chinese: 齿轮

# Synonyms, Antonyms and Related Words

Hydromatic, automatic
transmission, differential, differential
gear, freewheel,
gear, gear train, gearbox, gearing, gearshift, gearwheel, high, intermediate, low, neutral, overdrive, rack, reverse, standard transmission,
stick shift, synchromesh, transmission